Plumbing Basics: A Prerequisite for Installing a Bathtub
Plumbing Basics: A Prerequisite for Installing a Bathtub
Blog Article
How do you feel about Installing A Bathtub?
Mounting a bath tub isn't specifically brain surgery, however it does need solid plumbing, woodworking, as well as often, tiling skills. Replacing an old tub with a new one is likewise a moderately difficult project. If the old bathtub is readily available, the task can relocate rapidly; if you have to open a wall to remove the old tub and place the new bathtub, the task is a lot harder. In either situation, the job is within a house handyman's abilities, although you will need an assistant to move out the old tub as well as embeded in the new one. Make certain you have actually certified yourself for the task and also are comfortable attempting it. Rather than working with a professional to take over a halfway-completed task, it is better to think about employing one prior to you start. Chances are you might need an expert plumber to make tube connections.
This post will certainly help you install a new bathtub in your washroom if you have actually already gotten a brand-new bathtub and do not require to alter the arrangement of your previous supply of water pipes.
Your devices as well as material list must make up the following:
Preparing for the Installment
First of all, the sustaining structure provided with the bathroom ought to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the tap comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps system to prevent stress on the bath tub.
Fit the flexible faucet ports to the bottom of both taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you make use of all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, after that the first thing you should do is separate the water supply. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of removing the existing taps can be quite problematic because of the limited accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric all set for the remaining water that will originate from the pipes. As soon as the supply pipes have actually been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Using both wood boards under its feet, put the bathtub in the required placement. The wooden boards are valuable in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little points.
The following goal is to make sure that the tub is leveled all round. This can be attained by checking the level and changing the feet on the tub till the level checks out level.
To install taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression join; after that do the exact same for the other tap.
Switch on the water supply and also examine all joints and also new pipework for leakages and also tighten them if necessary. Fill up the bath tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and sealing around the bathtub should wait until the tub has actually been used at least once as this will resolve it right into its final placement.
Suitable New Taps
If the tails of the new taps are plastic, after that you will require a plastic connector to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in place in between the tap and also the sink. Protect the tap in place with the manufacturer supplied backnut. As soon as the faucet is securely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former kind ought to be linked to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture an inflexible seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, leading to problems with wetness as well as possible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to allow for the movement experienced when the bathtub is in use. The sealer can break rather early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly offered on the market. It is advisable to fit the tiles using waterproof or water-proof sticky and also cement.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
I found that blog posting about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when looking around the search engines. Loved our blog? Please share it. Let others locate it. We value reading our article about How to Install a Bathtub.
Drain woes? Connect. Report this page